GRAPHTEC FC8000 MANUAL PDF

Vinyl Cutter Download Graphtec FC, Vinyl Cutter Machine Download Software Installation & Operation Manual in pdf ( MB) > Download Now. Manually Adjusting the FC ARMS Sensor Level for Glossy Media and Glossy Laminated Prints. When using some glossy media or when using glossy. View and Download GRAPHTEC FC Series user manual online. Cutting Pro . FC Series Plotter pdf manual download.

Author: Gucage Yolabar
Country: Tanzania
Language: English (Spanish)
Genre: Education
Published (Last): 13 March 2013
Pages: 181
PDF File Size: 11.91 Mb
ePub File Size: 15.78 Mb
ISBN: 351-1-52431-885-2
Downloads: 77561
Price: Free* [*Free Regsitration Required]
Uploader: Yogrel

It will give error or malfunction when it has made mistake. Preface In addition to cutting marking film and other media, an FC series plotter can also be used as a pen plotter. cc8000

ARMS (Advanced Registration Mark Sensing system)

Page 37 Press the media lock to engage it, and then pull the leading edge out of the front of the plotter so that it completely covers the media sensor. Their display and meaning is as following.

CAUTION When cutting high intensity reflective media The backing sheet used for the high intensity reflective media is very soft, so it will need a reinforcement. Reading The Error Message 7 Operate switches and sensors following the instructions on the screen. If the loaded media is tilted as shown below, position of the scanned registration mark is shifted from the position where it should be.

Cut Area 50 m x mm 50 m x mm 50 m x mm 50 m x mm 50 m x mm expanded mode expanded mode. Perform following if these are the cause of the problem. Never use thinner, benzene, alcohol, or similar solvents to clean the casings; they will damage the casing’s finish.

  GABRIELA MISTRAL LAGAR PDF

It depends on the media specified by Graphtec and setting conditions. In addition to cutting marking film and other media, an FC series plotter can also be used as a pen plotter. Do not allow small mnual to touch the plotter. Settings Regarding Cutting Time Chapter 8: U sed to carry roll media and ensure its proper rotation.

What is the ARMS? The sensitivity of the registration mark sensor is automatically set by measuring the reflective level of the marks of the actual media. Distance between the registration marks can be Precision of print and cut position will be higher than the 1 axis adjusted.

Setting the Pouncing Tool Set the distance of the holes when continuous holes are to be punched. Angle control is applied if there is larger angle change than the angle specified as reference angle. Setting Speed of the Registration Mark Scan Speed of the tool carriage and media to scan the registration mark is set.

Preface In addition to cutting marking film and other media, an FC series gtaphtec can also be used as a pen plotter. X AXIS setting screen is displayed. Use of the plotter in such a condition may fraphtec in a fre hazard or electric shock.

Bigger registration mark size is better if there is difference in printing or media is set tilted.

Graphtec Manuals and Drivers

manusl Setting the Speed Set the speed of the tool that is used in each of the condition numbers. Page 11 Chapter 7: Axis alignment by the first mark After data is sent the first time, it can be copied multiple times without a PC. Setting Speed of the Registration Mark Scan of the tool carriage and media to scan the registration mark is set. Page of Go.

  ISO 17660-2 PDF

Always use the weaker setting for the push roller s between the two outside rollers. There are 8 different patterns of perforated lines set as 0 to 7, and the ratio of cut and uncut part differs in each tool is raised or the force is decreased for following length every 8 mm of fc0800 cut.

Check that the power is supplied to the electrical outlet. Previous cutting data will be cleared and newly sent data will be stored as cutting data if you send new data with 10 seconds or more interval from the time it finished cutting. It is used to check if the transmission of cutting graphtecc is performed correctly. This is called the initial blade direction adjust.

Graphtec Manuals and Drivers – SignWarehouse Product Support

Page Move the position of the light with strong scattered source. If you desire to load the material from the front, it is also possible to use the front loading.

The media must be at least mm in length. By pressing ‘print’ button you will print only current page. The rate of enlargement or shrinkage of the cutting data can be changed by settings.

grapphtec Default setting for page length is 2 m. There are following functions depending on the operation. For example, a white mark can be detected on a colored background. Recommended affixing media stiffness:

Author: admin